Plain Southern Powder Horns

The vast majority of original powder horns were as plain as they could be and still be functional. That means a flat pine (or other softwood) base plug and little or no carving of the throat; just enough work to contain powder and attach a strap. Many times a screw was used to attach a strap to the base plug. A grooved or simply reduced throat is enough to tie a strap around it. The two powder horns shown just below are based on an original southwest Virginia horn and are a little fancier than most with a turned base plug and carved rings at the throat. Even so, it is still much plainer than the carved and engraved horns from the French and Indian War. This horn could also be made with a turned and applied collar instead of the integral rings. The horn would dictate how it is approached.

Horn #7 - Side
Horn #7 – A SW. VA style powder horn
Horn #19 - A SW. VA horn in the basic style of Horn #7.
Horn #19 – A SW. VA horn in the basic style of Horn #7.

Please note the raw linen cord used to attach the horn in the photo below.   Cord was often found on southern outfits.    The outfit show below is much more historically correct for a southern mountain rifle than many of the sophisticated shot pouches and powder horns being recreated today.    Most of the original powder horns and shot pouches were very simple affairs, well worn and patched together.   You will see horns completely covered in leather to patch a hole or holes rather than just throw it away.   Even something as simple as a plain powder horn could not be easily replaced in the southern mountains and was highly valued.

I will make any plain powder horn with a flat base plug and simply carved throat and spout for $150 plus shipping. A horn like #7 with a turned, flat or domed base plug and carved rings would cost $210 plus shipping.

To order a powder horn or discuss any other project, use the Contact form to send me an e-mail. See FAQ for more information on ordering custom work. The availability of any particular horn design depends on the availability of an appropriate unfinished horn in my inventory.

Horn #3 - Bag #8 - A plain southern powder horn attached by linen cord to a Southern heart shaped shot pouch laying on a flat surface.
Horn #3 – Plain southern powder horn, Bag #8 – Southern Heart Shaped Shot Pouch
Horn #4 - Plain southern powder horn, 10 3/4" outside curve, 2 1/2" dia. base plug
Horn #4 – Plain southern powder horn, 10 3/4″ outside curve, 2 1/2″ dia. base plug
Horn #4 - Top of plain southern powder horn with a wedding ring carved at the end of a bell shaped tip.
Horn #4 – Top – Plain southern powder horn
Horn #8 - Top of a plain southern powder horn wiht a large wedding band carved a the beginning of a bell shaped tip just above the throat.
Horn #8 – Top – Plain southern powder horn
Horn #8 - Plain southern powder horn, 10 1/4" outside curve, 2 3/8" dia. base plug
Horn #8 – Plain southern powder horn, 10 1/4″ outside curve, 2 3/8″ dia. base plug
Plain southern powder horn with octagonal shaped tip.
Horn #9 – Plain Southern Powder Horn, 11″ outside curve, 2 1/2″ dia. base plug
Top view of plain southern powder horn with an octacgonal tip.
Horn #9 – Top – Plain southern powder horn

 

 

 

 

 

 

 

 

 

 

 

 

 

Right or Left Hand Carry Powder Horns?

There are both right hand and left hand powder horns shown above.   The question is what does that mean.   It refers to the side on which you carry the horn.   The tip always points forward and should wrap around your body.    In other words, the tip should not jut out so that it can catch on a passing object.

Technically,  a curve of the tip to the left as viewed from the top is a right hand carry horn and also from the right side of the cow.   A curve of the tip to the right would technically be a left hand carry horn and from the left side of the cow.   If there is no significant curve of the horn as viewed from the top, then the horn can be easily worn on either side.   Most horns have so little curve it really doesn’t matter.

Sometimes a horn that is technically a left hand horn might wrap around the body better on the right hand side and vice versa.    So,  in describing a horn for sale,  I will tell you whether a horn is technically a left hand or a right hand.  Then I will tell you on which side the horn was built to be carried,  if it is different.    I will also try to include a photo from the top of the horn so you can see the curve for yourself.     On which side you actually carry a horn, that is up to you.

Facebooktwitterredditpinterestlinkedinmail
Facebooktwitterlinkedinrss

18th Century Style Mens’ Pocketbook

Mens 18th C fraktur tooled pocketbook

Not too long ago, my osteopath told me I needed to take my overstuffed wallet out of my back pocket and ditch it. It was pretty ratty anyway; almost worn through in places. I shopped around for a replacement but just couldn’t find anything just right. I needed to carry my drivers license, registration, proof of insurance, disabled parking card, and medical insurance card as well as some cash, at least one debit card, and a couple grocery discount cards. That was about as much as I could slim down. I had about three times that much stuff in the old wallet, not including the receipts, notes, and other paperwork. It was basically a traveling file cabinet. What I finally decided to do was design a little 18th century style mens’ pocketbook based on the construction of my early VA shot pouch and several original cloth pocketbooks that I had seen.

Fraktur tooling on 18thC men's pocketbookShown here is the result of my efforts. It is still a little overstuffed, but better than what I had. It is made out of goat skin (any new one would probably have to be calf skin), consisting of two sets of pockets flat sewn with a center divider serving as the welt for each set. The pockets fold like the pages of a book with a flap closure.

 

Fraktur tooling on 18thC men's pocketbook

Fraktur tooling on 18thC men's pocketbook

Fraktur tooling on 18thC men's pocketbookI tooled every exposed surface. The outside is decorated with typically English stamped geometric designs consisting mainly of diagonal lines and stamped stars. The inside panels are tooled with fraktur designs. The stain is vinegar and iron.

If anybody would like one, I will make one with stamped decoration on the exterior panels for $120. If you want original fraktur tooling on the interior panels, that will cost you $180.  I will make a wallet with a single set of pockets for $80.  I will have to add 5.3% sales tax for VA residents. Shipping is $15.

Download the pattern here if you would like to make the pocketbook yourself.

 

Facebooktwitterredditpinterestlinkedinmail
Facebooktwitterlinkedinrss

Late Colonial Powder Horn

IMG_0044-101

 

This powder horn was made from a raw horn in a late colonial style. I scraped it down, carved and filed the spout in the traditional manner. The plain domed base plug was carved from pine and held in place with wooden pegs. I turned the stopper from a scrap piece of curly maple. The stopper was stained with aqua fortis, and the aqua fortis was used to age the horn giving it the golden yellow color. Just like with staining wood, you have to apply heat to the horn to activate the aqua fortis and get that nice yellow color. The spout was dyed with dark brown Rit dye. Walnut hulls would probably have been used originally and I intend to switch to natural dyes in the future. The schrimsaw is not a copy of anything in particular, but something to my liking using period motifs. The strap is from Shayna L. Matthews ( www.fiberwoodart.com ). I like her work quite a bit and have bought several straps from her.

If you are interested in a powder horn like this, use the Contact form to send me an e-mail. If you want me to make you a new horn similar to this one, an carved and engraved French and Indian War style horn, with YOUR name on it; it will cost you $600(plus shipping and applicable sales tax). See FAQ for more information on purchasing custom work.

IMG_0076-103
IMG_0056-102
IMG_0114-105
IMG_0099-104

Facebooktwitterredditpinterestlinkedinmail
Facebooktwitterlinkedinrss

Tin Powder Measure Set

This is a powder measure set that I created for Bag #12. It consists of a tin-plated steel powder measure, pan brush and vent pick.  The pan brush is horse hair with a tin ferrule and the vent pick is made of music wire.   Three flats are ground on the end of the vent pick to use in scraping out the touch hole. I can make you a powder measure set like this for $55 plus $8 for shipping. I will make just a measure for $25 plus $8 shipping.

If you are interested in this pan brush and powder measure set or one like it, use the Contact form to send me an e-mail. See FAQ for more information on purchasing custom work.

Tin powder measure, pan brush, and pick

Facebooktwitterredditpinterestlinkedinmail
Facebooktwitterlinkedinrss