Southern Banded Powder Horns

Southern Banded Powder Horns

On this page I have some southern  multi-banded powder horns.   These types of horns are typically found in North Carolina and south.  The single banded horns are covered on the Virginia Applied Tip Powder Horns page.   All these horns have applied tips with most being screw-tips.   If you see something you like,  use the Contact page to get in touch with me, and we can discuss making you a similar horn.

Horn #54 - Multi-banded southern style powder horn- Top
Horn #54 – Multi-banded southern style powder horn- Top
Horn #54 - Multi-banded southern style powder horn- Bottom
Horn #54 – Multi-banded southern style powder horn- Bottom

This medium sized horn (Horn #54) is a traditional right hand carry horn.   It is approximately 14 3/8″ around the outside curve and 12 1/4″ tip to tip not including the Walnut stopper.  The curly Maple base plug is approximately 2 3/4″ in diameter and is hollowed out better than half its length.  The horn weighs a little over 8 oz due to the very dense base plug.  The horn and base plug are stained with ferric nitrate and normally aged.

Horn #54 - Multi-banded southern style powder horn- Outside
Horn #54 – Multi-banded southern style powder horn- Outside
Horn #54 - Multi-banded southern style powder horn- Inside
Horn #54 – Multi-banded southern style powder horn- Inside
Horn #51 - VA inspired multi-banded powder horn- Top
Horn #51 – VA inspired multi-banded powder horn- Top
Horn #51 - VA inspired multi-banded powder horn- Bottom
Horn #51 – VA inspired multi-banded powder horn- Bottom

This medium to large sized horn (Horn #51) is a traditional left hand carry inspired by some Early Virginia horns shown in Jay Hopkin’s book Bone Tipped & Banded Horns.  While it is a traditional left hand carry,  it can be carried on the right.  It is 16″ around the outside curve and 12 3/4″ tip to tip not including the stopper.   The Black Walnut base plug is 2.72″ in diameter and hollowed out about 3/4 of its length.   There is also a Black Walnut stopper in the horn screw-tip.  There is no stain on the horn.  It is all finished with Tried & True (linseed oil and beeswax).     This horn is thin and translucent its entire length.  It weighs a little under 8 oz.

Horn #51 - VA inspired multi-banded powder horn- Outside
Horn #51 – VA inspired multi-banded powder horn- Outside
Horn #51 - VA inspired multi-banded powder horn- Inside
Horn #51 – VA inspired multi-banded powder horn- Inside
Horn #50 - NC inspired multi-banded powder horn- Top
Horn #50 – NC inspired multi-banded powder horn- Top
Horn #50 - NC inspired multi-banded powder horn- Bottom
Horn #50 – NC inspired multi-banded powder horn- Bottom

This medium sized horn (Horn #50) is a traditional right hand carry inspired by the horns found in North Carolina.   It is about 14″ around the outside curve and about 11 1/4″ tip to tip.  The walnut base plug  is 2 1/4″ in diameter hollowed out about 3/4 of it’s length.  The applied-tip is Axis deer antler.   The stopper is walnut.

Horn #50 - NC inspired multi-banded powder horn- Outside
Horn #50 – NC inspired multi-banded powder horn- Outside
Horn #50 - NC inspired multi-banded powder horn- Inside
Horn #50 – NC inspired multi-banded powder horn- Inside
Horn #47 - Southern multi-banded powder horn- Top
Horn #47 – Southern multi-banded powder horn- Top
Horn #47 - Southern multi-banded powder horn- Bottom
Horn #47 – Southern multi-banded powder horn- Bottom

This little horn (Horn #47) is a traditional left hand horn, but can be carried either way.    It is about 12″ around the outside curve and 10″ tip to tip.   The walnut base plug is 2.03″ in diameter and hollowed out about 3/4 of it’s length.  The applied-tip is Axis deer antler.  The stopper is walnut.

Horn #47 - Southern multi-banded powder horn- Outside
Horn #47 – Southern multi-banded powder horn- Outside
Horn #47 - Southern multi-banded powder horn- Inside
Horn #47 – Southern multi-banded powder horn- Inside
Horn #65 - Southern multi-banded powder horn - Top
Horn #65 – Southern multi-banded powder horn – Top
Horn #65 - Southern multi-banded powder horn - Bottom
Horn #65 – Southern multi-banded powder horn – Bottom

 The next horn (Horn #65) is a historically left hand horn carried on the right side so that it wraps around the body.    It is about 14 5/8″ finial to tip, not including the stopper,  around the outside curve.   Tip to tip it is 13″.  The base plug is about 2 5/8″ in diameter.   The base plug is hollowed out about 3/4 of its length.  The Axis deer antler tip and horn collar are pegged on.   The base plug and stopper are both Black Walnut.

Horn #65 - Southern multi-banded powder horn - Outside
Horn #65 – Southern multi-banded powder horn – Outside
Horn #65 - Southern multi-banded powder horn - Inside
Horn #65 – Southern multi-banded powder horn – Inside

The horn (#27) below is a particularly small one.   It is pretty straight and could easily be, historically, either a right or a left hand carry;  about 11″ around the outside curve staple to stopper.   The base plug is a little less than 2 1/4″ in diameter.   It has a screw-tip with a female thread.  The base plug is hollowed out about 3/4 of its length.

Horn #27 - A small multi-banded screw-tip powder horn.
Horn #27 – A small multi-banded screw-tip powder horn.
Horn #27 - A small multi-banded screw-tip powder horn.
Horn #27 – A small multi-banded screw-tip powder horn.

Horn #31 - Southern multi-banded, screw-tip powder horn - TopThe following horn (Horn #31) is historically a left hand carry, but is  setup as a right hand carry.   It can be carried either side without a problem.  It is about 13 1/2″ staple to stopper around the outside curve.   The base plug is a little less than 2 1/4″ in diameter.  It has a screw-tip with a female thread.  The base plug is hollowed out about 3/4 of its length.

Horn #31 - Southern multi-banded, screw-tip powder horn - Inside curve
Horn #31 – Southern multi-banded, screw-tip powder horn – Inside curve
Horn #31 - Southern multi-banded, screw-tip powder horn - Outside curve
Horn #31 – Southern multi-banded, screw-tip powder horn – Outside curve

Horn #32 - Southern multi-banded, screw-tip powder horn - TopThe following horn (Horn #32) is historically  a left hand carry, but is marked assuming a right hand carry.  It can be carried on either side.    It is about 15″ button to stopper around the outside curve.   The base plug is a little more than 2 3/8″ in diameter.  It has a screw-tip with a female thread.  The base plug is hollowed out about 1/2 of its length.  There  is  a slight gap between the base ring and the base plug, but the horn is air tight.   This horn is also a little on the heavy side at  7.4 oz.   All that being said,  this is still a very nice looking little horn.

Horn #32 - Southern Multi-banded, screw-tip powder horn - Inside Curve
Horn #32 – Southern Multi-banded, screw-tip powder horn – Inside Curve
Horn #32 - Southern Multi-banded, screw-tip powder horn - Outside Curve
Horn #32 – Southern Multi-banded, screw-tip powder horn – Outside Curve
Horn #33 - Southern multi-banded, applied -tip powder horn - Top
Horn #33 – Southern multi-banded, applied -tip powder horn – Top

The following horn (Horn #33) is a big one inspired by some early Virginia horns in Jay Hopkin’s book.  I think it would work well with my early Virginia shot pouch.  It is historically  a right hand carry, but I think it would work better as a left hand carry.    It can be carried on either side.    It is about 17″ button to stopper around the outside curve.   The base plug is a little more than 2 5/8″ in diameter.  It has an applied tip made up from horn and antler.   The base plug is hollowed out about 3/4 of its length.  This horn is actually very light weight for its size.  It weighs 6.8 oz.

Horn #33 - Southern multi-banded, applied -tip powder horn - Inside
Horn #33 – Southern multi-banded, applied -tip powder horn – Outside
Horn #33 - Southern multi-banded, applied -tip powder horn - Outside
Horn #33 – Southern multi-banded, applied -tip powder horn – Inside

All these multi-banded, applied tip horns are priced at $295 plus shipping for a bespoke horn.   Availability of any particular style, size or carry side of powder horn depends on my stock of raw horns.  If you see something you like,  use the Contact page to get in touch with me, and we can discuss making you a similar horn.

Shipping/insurance on a single multi-banded horn is $20 to $25  depending on destination withing the continental US.   VA residents will have to pay an additional 5.3%  to 7% sales tax depending on their locality.

Right or Left Hand Carry?

What is right or left hand carry?  Simply, it is the side of the body on which a horn is intended to be worn.  Historically,  a curve of the tip to the left as viewed from the top is a right hand carry horn and also from the right side of the cow.   A curve of the tip to the right would historically  be a left hand carry horn and from the left side of the cow.   If there is no significant curve of the horn as viewed from the top, then the horn can be easily worn on either side with no conflict.   Most horns have so little curve it really doesn’t matter much and the modern pattern of carry is frequently opposite of the historical pattern.

Carrying a horn on the same side of the body as it came from the cow results in the tip pointing toward the body and the base pointing away from the body.   I also like the base of the horn to point to ward the body, as do many modern wearers, so I usually use the opposite side horn and rotate it about 90 degrees so that both the tip and the base of the horn point into the body.    This makes a horn from the left side of the cow into a powder horn you can carry on the right side of the body.     This is my personal preference, but not generally historically correct.  Historically,  powder horns were usually carried on the same side of the body as they came from on the cow.   If you want to be completely historically correct,  you need to understand that.

Sometimes a horn that is technically a left hand horn might wrap around the body better on the right hand side and vice versa.    So,  in describing a horn,  I will tell you whether a horn is historically a left hand or a right hand.  Then I will tell you on which side the horn was built to be carried,  if it is different.    I will also try to include a photo from the top of the horn so you can see the curve for yourself.     On which side you actually carry a horn, that is up to you.

What is an American Longrifle?

Contemporary American longrifle.Contemporary American longrifle.
Contemporary Longrifle in the Style of 1775-1785 Augusta/Rockbridge County, Virginia

“From a flat bar of soft iron, hand forged into a gun barrel; laboriously bored and rifled with crude tools; fitted with a stock hewn from a maple tree in the neighboring forest; and supplied with a lock hammered to shape on the anvil; an unknown smith, in a shop long since silent, fashioned a rifle which changed the whole course of world history; made possible the settlement of a continent; and ultimately Freed our country of foreign domination.

Light in weight; graceful in line; economical in consumption of powder and lead; fatally precise; distinctly American; it sprang into immediate popularity; and for a hundred years was a model often slightly varied but never radically changed.

Legend regarding this rifle which have never been confirmed have drifted out of the dusty past; inaccuracies have passed for facts. Few writers have given more than a passing word to a weapon which deserves a lasting place in history, and it is a pleasure to present herewith the data collected during the past ten years and to dedicate this work to the KENTUCKY RIFLE.”

—- Capt. John G. Dillon, 1924, From his book The Kentucky Rifle

It is hard to beat John Dillon’s description of an Kentucky Rifle, the popular name for the American longrifle. This hints at the fact that there are a lot of names for basically the same thing. There is even some disagreement as to whether you spell it longrifle or long rifle. Generically, we refer to the American longrifle which includes all longrifles made in what would become the United States of America. We refer to longrifles made in specific States or regions by adding the State or region names such as in Pennsylvania longrifles or Southern longrifles; or even Kentucky longrifles, not to be confused with Kentucky Rifles. Remember that Kentucky Rifles is the popular name for all longrifles and is equivalent in use to American longrifles.

Fry & Jefferson Map from 1751 showing great wagon road
Fry & Jefferson Map 1751 showing the Great Wagon Road (red) and the later Wilderness Road (blue)
The Kentucky Rifle has been referred to in print since at least the third quarter of the 19th century. Some believe that the name came from the song “Hunters of Kentucky” by Samuel Woodworth recounting Andrew Jackson’s victory in the Battle of New Orleans in 1812. The song referred to “Kentucky rifles” carried by the riflemen from Kentucky who were prominent in that victory. However, the American longrifle was not just made in Kentucky, it was made in many states along the Eastern Seaboard, including Pennsylvania, Maryland, Virginia(West Virginia), Kentucky, North Carolina, Tennessee, South Carolina, Georgia, Alabama, Ohio, Indiana, New York and New England. In fact, the first longrifles carried into Kentucky via the Great Wagon Road and the Wilderness Road were made in Pennsylvania and possibly Virginia. The manufacture and evolution of the American longrifle followed settlers down the Great Wagon Road from Philadelphia into western Pennsylvania, Maryland, Virginia, and North Carolina and then west along the Wilderness Road into Tennessee and Kentucky. In one British officer’s account of the effectiveness of the “over the mountains men” from Kentucky and Tennessee in the southern campaigns of the American Revolution of 1780 and 1781, he described their rifles as having been “chiefly made in Lancaster, and two or three neighboring towns in that vicinity, in Pennsylvania.”

The American longrifle originated in and about Lancaster, Pennsylvania in the second quarter of the 18th century and was made well into the second quarter of the 19th century. Martin Mylin, a German Swiss gunsmith, established a shop outside Lancaster in 1719, and is credited with making the first American longrifle about 1740. Eventually, the American longrifle gave way to more sophisticated, mass produced firearms starting with the Industrial Revolution in America around 1840. However, production of the American longrifle never completely ceased. Gunsmiths were making similar guns throughout the 19th century. Mostly, these were high end target rifles, but there were back country gunsmiths making longrifles for subsistence hunting in the Appalachians well into the 20th century. With the renewed interest in all things early American in the 1920’s and 30’s (the Colonial Revival period) as a result of the American sesquicentennial, there was a renewed interest in the Kentucky rifle. It was during this period that John Dillon wrote his book heralding an ever increasing interest in collecting, and recreating these uniquely American firearms.

But I still haven’t really told you what makes a gun an American longrifle. Well, they are long (usually five feet or more), graceful, slender, exceedingly accurate (by the standards of the day), muzzleloading (gunpowder and a round lead ball covered by a cloth patch were loaded from the muzzle(front) of the barrel), rifled (spiral grooves (furrows) were cut into the bore of the barrel to impart a stabilizing spin on the bullet thereby dramatically increasing accuracy), of relatively small caliber (average was around 50 caliber, decreasing into the 19th century), with either flintlock or percussion sidelock ignition systems, a full length wood stock, and usually a patchbox or grease hole on the lock side of the butt stock. The barrels were almost always octagon (“squared” in 18th century terminology) and tapered toward the muzzle and flared back out starting a few inches from the muzzle. This taper and flare (swamp) was generally very subtle giving way to straight tapered and then straight barrels in the mid 19th century. These guns were primarily mounted with brass fixtures (butt piece, toe plate, guard, side plate, thimbles and nose piece); but some, most notably in the South, had iron mounts; and, very rarely, there was a silver mounted gun. Many of these guns were decorated with baroque and rococo carving and engraving as well as inlays of silver and brass wire and sheet. Some of these rifles were extremely ornate and were one of the first truly American art forms. They are now recognized as a significant form of American decorative art and people collect them as such. This is what has driven the price of the best original flintlock American longrifles well into six figures.

The roots of the American longrifle are in the German rifles, or Jaegers, that were brought to this country by early German settlers and gunsmiths. Among other stylistic changes, the barrels of the Jaegers were lengthened, and the caliber reduced to produce the uniquely American longrifle which made more efficient use of powder and was very accurate at long range. The American longrifle developed to serve the needs of commercial hunters traveling to the frontier and beyond to harvest deer skins for export. These commercial hunters or “longhunters” have long been portrayed as pioneers and explorers of European origin such as Daniel Boone and Davy Crockett. However, there is good reason to believe that as many as half of the early longrifles went to native American hunters who had been using European arms to harvest skins for export to Europe since the first contact with European traders in the 16th century.

There is lots more that I could write about the American longrifle, but the best way to learn about them is to look at them and handle them. On this site you will find photos of some of the better ones that I have made in my Portfolio as well as photos of original longrifles that I and others have owned in the Antique Longrifles Gallery. Look them over good, get some good books on the subject, and seek out original longrifles for study at museums, gun shows, and private owners.

Bibliography

  • The Kentucky Rifle by Capt. John Dillon
  • The Kentucky Rifle in its Golden Age by Joe Kindig Jr.
  • Rifles of Colonial America, Volume 1 & Volume 2by George Shumway
  • Recreating the American Longrifle by William Buchele, George Shumway, and Peter Alexander
  • The Gunsmith of Grenville County, Building the American Longrifle by Peter Alexander
  • The American Rifle: At the Battle at Kings Mountain by C.P. Russell, U.S. Department of the Interior, National Park Service, Washington, D.C., 1941
  • Rifle Making in the Great Smoky Mountains by Arthur I. Kendall, U.S. Department of the Interior, National Park Service, Washington, D.C., 1941